CERT mailing list archives
Courtesy Copy: TA14-017A: UDP-Based Amplification Attacks
From: "US-CERT" <US-CERT () ncas us-cert gov>
Date: Tue, 27 Feb 2018 20:01:19 -0600
DHS Seal and US-CERT logo National Cyber Awareness System: *TA14-017A: UDP-Based Amplification Attacks [ https://www.us-cert.gov/ncas/alerts/TA14-017A ]* "Updated 02/27/2018 08:45 PM EST Added information on Memcache-based reflection DDoS attacks " Original release date: January 17, 2014 *Systems Affected* Certain application-layer protocols that rely on the User Datagram Protocol (UDP) have been identified as potential attack vectors. These include * Domain Name System (DNS), * Network Time Protocol (NTP), * Connection-less Lightweight Directory Access Protocol (CLDAP), * Character Generator Protocol (CharGEN), * Simple Service Discovery Protocol (SSDP), * BitTorrent, * Simple Network Management Protocol version 2 (SNMPv2), * Kad, * Portmap/Remote Procedure Call (RPC), * Quote of the Day (QOTD), * Multicast Domain Name System (mDNS), * Network Basic Input/Output System (NetBIOS), * Quake Network Protocol, * Steam Protocol, * Routing Information Protocol version 1 (RIPv1), * Lightweight Directory Access Protocol (LDAP), * Trivial File Transfer Protocol (TFTP), and * Memcache. *Overview* A distributed reflective denial-of-service (DRDoS) attack is a form of distributed denial-of-service (DDoS) that relies on publicly accessible UDP servers and bandwidth amplification factors (BAFs) to overwhelm a victims system with UDP traffic. *Description* By design, UDP is a connection-less protocol that does not validate source Internet Protocol (IP) addresses. Unless the application-layer protocol uses countermeasures such as session initiation in Voice over Internet Protocol, an attacker can easily forge the IP packet datagram (a basic transfer unit associated with a packet-switched network) to include an arbitrary source IP address. [1 [ https://tools.ietf.org/html/rfc3261 ]] When many UDP packets have their source IP address forged to the victim IP address, the destination server (or amplifier) responds to the victim (instead of the attacker), creating a reflected denial-of-service (DoS) attack. Certain commands to UDP protocols elicit responses that are much larger than the initial request. Previously, attackers were limited by the linear number of packets directly sent to the target to conduct a DoS attack; now a single packet can generate between 10 and 100 times the original bandwidth. This is called an amplification attack, and when combined with a reflective DoS attack on a large scale, using multiple amplifiers and targeting a single victim, DDoS attacks can be conducted with relative ease. The potential effect of an amplification attack can be measured by BAF, which can be calculated as the number of UDP payload bytes that an amplifier sends to answer a request, compared to the number of UDP payload bytes of the request. [2 [ http://www.christian-rossow.de/articles/Amplification_DDoS.php ]] [3 [ http://www.christian-rossow.de/publications/amplification-ndss2014.pdf ]] The following is a list of known protocols and their associated BAFs. US-CERT offers thanks to Christian Rossow for providing this information. For more information on BAFs, please see Christian'sblog [ http://www.christian-rossow.de/articles/Amplification_DDoS.php ] and associated research paper [ http://www.christian-rossow.de/publications/amplification-ndss2014.pdf ]. *Protocol* *Bandwidth Amplification Factor* ** *Vulnerable Command* DNS 28 to 54 see:TA13-088A [ https://www.us-cert.gov/ncas/alerts/TA13-088A ][4 [ https://www.us-cert.gov/ncas/alerts/TA13-088A ]] NTP 556.9 see:TA14-013A [ https://www.us-cert.gov/ncas/alerts/TA14-013A ][5 [ https://www.us-cert.gov/ncas/alerts/TA14-013A ]] SNMPv2 6.3 GetBulk request NetBIOS 3.8 Name resolution SSDP 30.8 SEARCH request CharGEN 358.8 Character generation request QOTD 140.3 Quote request BitTorrent 3.8 File search Kad 16.3 Peer list exchange Quake Network Protocol 63.9 Server info exchange Steam Protocol 5.5 Server info exchange Multicast DNS (mDNS) 2 to 10 Unicast query RIPv1 131.24 Malformed request Portmap (RPCbind) 7 to 28 Malformed request LDAP 46 to 55 Malformed request [ https://ldapscan.shadowserver.org/ ][6 [ https://ldapscan.shadowserver.org/ ]] CLDAP [7 [ https://www.akamai.com/us/en/about/our-thinking/threat-advisories/connection-less-lightweight-directory-access-protocol-reflection-ddos-threat-advisory.jsp ]] 56 to 70 TFTP [23 [ https://www.researchgate.net/publication/284077229_TFTP_DDoS_amplification_attack ]] 60 Memcache 10,000 to 51,000 In March 2015, the CERT Coordination Center of the Software Engineering Institute issued Vulnerability Note VU#550620 describing the use of mDNS in DRDoS attacks. Attackers can leverage mDNS by sending more information than can be handled by the device, thereby causing a DoS condition. [8 [ https://www.kb.cert.org/vuls/id/550620 ]] In July 2015, Akamai Technologies' Prolexic Security Engineering and Research Team (PLXsert) issued a threat advisory describing a surge in DRDoS attacks using RIPv1. Malicious actors are leveraging the behavior of RIPv1 for DDoS reflection through specially crafted request queries. [9 [ http://www.stateoftheinternet.com/ ]] In August 2015, Level 3 Threat Research Labs reported a new form of DRDoS attack that uses portmap. Attackers are leveraging the behavior of the portmap service through spoofed requests to flood a victims network with UDP traffic. [10 [ http://blog.level3.com/security/a-new-ddos-reflection-attack-portmapper-an-early-warning-to-the-industry/ ]] In October 2016, Corero Network Security reported a new DDoS amplification attack exploiting LDAP directory services servers against its customers. [11 [ https://www.corero.com/company/newsroom/press-releases/corero-warns-of-powerful-new-ddos-attack-vector-with-potential-for-terabit-scale-ddos-events/%5d ]] In November 2017, Netlab 360 reported that CLDAP is now the third most common DRDoS attack, behind DNS and NTP attacks. [12 [ http://blog.netlab.360.com/cldap-is-now-the-3rd-reflection-amplified-ddos-attack-vector-surpassing-ssdp-and-chargen-en ]] In February 2018, SENKI reported an increase in Memcache-based reflection DDoS attacks (via UDP/TCP port 11211) with an unprecedented amplification factor. [24 [ http://www.senki.org/memcached-on-port-11211-udp-tcp-being-exploited/ ]] *Impact* Attackers can use the bandwidth and relative trust of large servers that provide the UDP protocols provided in this alert to flood victims with unwanted traffic and create a DDoS attack. *Solution* *Detection* Detection of DRDoS attacks is not easy because of their use of large, trusted servers that provide UDP services. Network operators of these exploitable services may apply traditional DoS mitigation techniques. To detect a DRDoS attack, watch out for abnormally large responses to a particular IP address, which may indicate that an attacker is using the service. There are a few things victims of DRDoS attacks can do to detect such activity and respond: * Detect and alert large UDP packets to higher order ports. * Detect and alert on any non-stateful UDP packets. (A simple Snort example is below. The approach will need to be customized to each environment with a whitelist and known services. Simple Snort rule example for stateless UDP check var HOME_NET [10.10.10.20] preprocessor stream5_global: track_ip yes, track_tcp yes,track_udp yes,track_icmp no,max_tcp 262144, max_udp 131072 preprocessor stream5_ip: timeout 180 preprocessor stream5_tcp: policy first, use_static_footprint_sizes preprocessor stream5_udp: timeout 180, ignore_any_rules alert udp HOME_NET 1024: -> any any (msg:"UDP Session start"; flowbits:set,logged_in; flowbits:noalert; sid: 1001;) alert udp any any -> HOME_NET 1024: (msg:"UDP Stateless"; flowbits:isnotset,logged_in; sid: 1002) * Upstream providers should maintain updated contacts and methods with downstream customers to send alerts by network. In general, network and server administrators for Internet service providers (ISPs) should use the following best practices to avoid becoming amplifier nodes: * Use network flow to detect spoofed packets. (See the Mitigation section below for information on verifying spoofed traffic before blocking that traffic.) * Use network flow or other summarized network data to monitor for an unusual number of requests to at-risk UDP services. * Use network flow to detect service anomalies (e.g., bytes-per-packet and packets-per-second anomalies). *Mitigation* The following steps can help mitigate a DRDoS attack: * Use stateful UDP inspectionssuch as reflexive access control liststo reduce the impact to critical services on border firewalls or border routers. [13] * Use a Border Gateway Protocol (BGP) to create a Remotely Triggered Blackhole, preferably in coordination with upstream providers or ISPs. [14] * Maintain a list of primary upstream provider emergency contacts to coordinate responses to attacks. Upstream providers should conduct mitigation in coordination with downstream customers. In general, ISP network and server administrators should use the following best practices to avoid becoming amplifier nodes: * Regularly update software and configurations to deny or limit abuse (e.g., DNS response rate limit). [15 [ https://kb.isc.org/article/AA-01000/0/A-Quick-Introduction-to-Response-Rate-Limiting.html ]] [16 [ https://tools.ietf.org/html/bcp38 ]] [17 [ https://tools.ietf.org/html/bcp84 ]] * Disable and remove unwanted services, or deny access to local services over the Internet. * Use UDP-based protocolse.g., quality of service (QoS) on switching and routing devicesto enable network-based rate-limiting to legitimate services provided over the Internet. * Work with Customer Provider Edge manufacturers for secure configuration and software. [18] As a service provider, to avoid any misuse of Internet resources: * Use ingress filtering to block spoofed packets (See the Spoofer Project [19 [ https://spoofer.caida.org/ ]], and IETF BCP 38 and BCP 84 guidelines). [20] * Use traffic shaping on UDP service requests to ensure repeated access to over-the-Internet resources is not abusive. [21 [ https://tools.ietf.org/html/rfc2475 ]] [22 [ https://tools.ietf.org/html/rfc3260 ]] *References* * [1] SIP: Session Initiation Protocol [ https://tools.ietf.org/html/rfc3261 ] * [2] Amplification Hell: Abusing Network Protocols for DDoS (link is external) [ http://www.christian-rossow.de/articles/Amplification_DDoS.php ] * [3] Amplication Hell: Revisiting Network Protocols for DDoS Abuse (link is external) [ http://www.christian-rossow.de/publications/amplification-ndss2014.pdf ] * [4] DNS Amplification Attacks [ https://www.us-cert.gov/ncas/alerts/TA13-088A ] * [5] NTP Amplification Attacks Using CVE-2013-5211 [ https://www.us-cert.gov/ncas/alerts/TA14-013A ] * [6] Open LDAP Scanning Project [ https://ldapscan.shadowserver.org/ ] * [7] CLDAP Reflection DDoS (link is external) [ https://www.akamai.com/us/en/about/our-thinking/threat-advisories/connection-less-lightweight-directory-access-protocol-reflection-ddos-threat-advisory.jsp ] * [8] VU#550620: Multicast DNS (mDNS) implementations may respond to unicast queries originating outside the local link [ https://www.kb.cert.org/vuls/id/550620 ] * [9] RIPv1 Reflection DDoS [Medium Risk] (link is external) [ https://www.akamai.com/us/en/multimedia/documents/state-of-the-internet/ripv1-reflection-ddos-threat-advisory.pdf ] * [10] A New DDoS Reflection Attack: Portmapper; An Early Warning to the Industry (link is external) [ http://blog.level3.com/security/a-new-ddos-reflection-attack-portmapper-an-early-warning-to-the-industry/ ] * [11] Corero Warns of Powerful New DDoS Attack Vector (link is external) [ https://www.corero.com/company/newsroom/press-releases/corero-warns-of-powerful-new-ddos-attack-vector-with-potential-for-terabit-scale-ddos-events/ ] * [12] CLDAP is Now the No.3 Reflection Amplified DDoS Attack Vector, Surpassing SSDP and CharGen (link is external) [ http://blog.netlab.360.com/cldap-is-now-the-3rd-reflection-amplified-ddos-attack-vector-surpassing-ssdp-and-chargen-en/ ] * [13] Configuring IP Session Filtering (Reflexive Access Lists) (link is external) [ https://www.cisco.com/c/en/us/td/docs/ios/12_2/security/configuration/guide/fsecur_c/scfreflx.html ] * [14] Remotely-Triggered Black Hole (RTBH) Routing (link is external) [ http://packetlife.net/blog/2009/jul/6/remotely-triggered-black-hole-rtbh-routing/ ] * [15] A Quick Introduction to Response Rate Limiting [ https://kb.isc.org/article/AA-01000/0/A-Quick-Introduction-to-Response-Rate-Limiting.html ] * [16] Network Ingress Filtering: Defeating Denial of Service Attacks Which Employ IP Source Address Spoofing [ https://tools.ietf.org/html/bcp38 ] * [17] Ingress Filtering for Multihomed Networks [ https://tools.ietf.org/html/bcp84 ] * [18] Abuse of Customer Premise Equipment and Recommended Actions (link is external) [ https://resources.sei.cmu.edu/asset_files/WhitePaper/2014_019_001_312679.pdf ] * [19] The Spoofer Project [ https://spoofer.caida.org/ ] * [20] Abuse of Customer Premise Equipment and Recommended Actions (link is external) [ https://resources.sei.cmu.edu/asset_files/WhitePaper/2014_019_001_312679.pdf ] * [21] An Architecture for Differentiated Services [ https://tools.ietf.org/html/rfc2475 ] * [22] New Terminology and Clarifications for Diffserv [ https://tools.ietf.org/html/rfc3260 ] * [23] TFTP DDoS Amplification Attack (link is external) [ https://www.researchgate.net/publication/284077229_TFTP_DDoS_amplification_attack ] * [24] Memcached on Port 11211 UDP & TCP Being Exploited [ http://www.senki.org/memcached-on-port-11211-udp-tcp-being-exploited/ ] *Revisions* * February 9, 2014 Initial Release * March 7, 2014 Updated page to include research links * July 13, 2015 Added RIPv1 as an attack vector * August 19, 2015 Added Multicast DNS (mDNS) and Portmap (RPCbind) as attack vectors * April 13, 2016 Updated detection and mitigation information * November 4, 2016 Updated for LDAP attack vector * December 4, 2017 Added information on CLDAP as an attack vector * December 6, 2017 Added information on TFTP as an attack vector * February 27, 2018 Added information on Memcache as an attack vector ________________________________________________________________________ This product is provided subject to this Notification [ http://www.us-cert.gov/privacy/notification ] and this Privacy & Use [ http://www.us-cert.gov/privacy/ ] policy. ________________________________________________________________________ A copy of this publication is available at www.us-cert.gov [ https://www.us-cert.gov ]. If you need help or have questions, please send an email to info () us-cert gov. Do not reply to this message since this email was sent from a notification-only address that is not monitored. To ensure you receive future US-CERT products, please add US-CERT () ncas us-cert gov to your address book. OTHER RESOURCES: Contact Us [ http://www.us-cert.gov/contact-us/ ] | Security Publications [ http://www.us-cert.gov/security-publications ] | Alerts and Tips [ http://www.us-cert.gov/ncas ] | Related Resources [ http://www.us-cert.gov/related-resources ] STAY CONNECTED: Sign up for email updates [ http://public.govdelivery.com/accounts/USDHSUSCERT/subscriber/new ]
Current thread:
- Courtesy Copy: TA14-017A: UDP-Based Amplification Attacks US-CERT (Feb 27)