Re: Native VLAN for Huawei MA5616 DSLAM

[Tina TSOU <Tina.Tsou.Zouting () huawei com>]

Dear Shahab,
Thank you for your prompt reply.
You can change to CCUE main board, then check the version, as far as I know, the software on CCUE shipped are all R312 
above, so u don't need to upgrade software.

Thank you,
Tina

On Aug 13, 2013, at 2:48 AM, "Shahab Vahabzadeh" <sh.vahabzadeh () gmail com<mailto:sh.vahabzadeh () gmail com>> wrote:

Dear Tina,
How can I upgrade the version? main board must change or it can upgrade with changing software/firmware?
Thank


On Tue, Aug 13, 2013 at 6:29 AM, Tina TSOU <Tina.Tsou.Zouting () huawei com<mailto:Tina.Tsou.Zouting () huawei com>> 
wrote:
Dear Shahab,
Thank you for more information.
CCUB main board doesn’t support native-VLAN setting, only CCUE main board supports it, the version should be upgraded 
to R312 above.

Thank you,
Tina

From: Shahab Vahabzadeh [mailto:sh.vahabzadeh () gmail com<mailto:sh.vahabzadeh () gmail com>]
Sent: 2013年8月12日 0:51
To: Tina TSOU; Zharov Oleg; nanog
Cc: Georgi Genov

Subject: Re: Native VLAN for Huawei MA5616 DSLAM

Dear Tina,
Thanks for your reply,
I have done the same example you told but there is no native-vlan command inside interface eth 0/0.
here my configuration and version of device, maybe firmare does not support it.
MA5616#display current-configuration

[vlan-config]
  <vlan-config>
 vlan 2 smart
 port vlan 2 0/0 0

MA5616#display board 0
  -------------------------------------------------------------------------
  SlotID  BoardName  Status           SubType0 SubType1    Online/Offline
  -------------------------------------------------------------------------
  0       H831CCUB   Active_normal    EP1A     ASDA
  1       H835ADLE   Auto_find
  2       H835ADLE   Auto_find
  3       H835ADLE   Auto_find
  4       H835ADLE   Auto_find
  5       H831PDIA   Normal
  -------------------------------------------------------------------------

MA5616#display version

  Command:
          display version

  VERSION : MA5616V800R308C01
  PATCH   : SPC200 SPH508 HP2108
  PRODUCT : MA5616

  Mainboard Running Area Information:
 --------------------------------------------
  Current Program Area : Area A
  Current Data Area : Area A

  Program Area A Version : MA5616V800R308C01
  Program Area B Version : MA5616V800R308C01

  Data Area A Version : MA5616V800R308C01
  Data Area B Version : MA5616V800R308C01
 --------------------------------------------

MA5616(config)#interface eth 0/0

MA5616(config-if-eth-0/0)#?
---------------------------------------------
  Command of eth Mode:
---------------------------------------------
auto-neg              Enable/Disable port negotiation
combo-mode            Switch working mode of COMBO port
display               Display information
duplex                Set duplex
flow-control          Support flow control
line                  Line test
mdi                   Line-adaptive function
mirror                Add mirror
network-role          Network role
port                  Set TX optical power threshold
quit                  Exit from current mode and enter prior mode
reset                 Clear port statistics
return                Enter the privileged mode
shutdown              Deactivate port
speed                 Rate
switch                Switch language mode
traffic-suppress      Set port traffic suppression
undo                  Negate a command or set its defaults

Thanks


On Mon, Aug 12, 2013 at 5:51 AM, Tina TSOU <Tina.Tsou.Zouting () huawei com<mailto:Tina.Tsou.Zouting () huawei com>> 
wrote:
Dear all,
Only for the uplink GE, the native VLAN can be configured, it can not be configured for NNI EPON/GPON and UNI DSL port.

//if the uplink port is GE, then configure a new VLAN 2
huawei(config)#vlan 2
//add the uplink GE 0/0 0 to VLAN 2
huawei(config)#port vlan 2 0/0 0
//change to uplink card interface view
huawei(config)#interface eth 0/0
//change native vlan of uplink GE to 2
huawei(config-if-eth-0/0)#native-vlan 0 vlan 2


Thank you,
Tina

On Aug 11, 2013, at 6:44 AM, "Shahab Vahabzadeh" <sh.vahabzadeh () gmail com<mailto:sh.vahabzadeh () gmail com>> wrote:

> Only these interface's are available under:
>
> MA5616(config)# interface ?
> > adsl
> > emu
> > eponnni
> > eth
> > gponnni
> > h248
> > loopback
> > meth
> > null
> > shl
> > vdsl
> > vlanif
>
>
> Thanks
>
>
> On Sun, Aug 11, 2013 at 4:55 PM, Shahab Vahabzadeh
> <sh.vahabzadeh () gmail com<mailto:sh.vahabzadeh () gmail com>>wrote:
>
> > Dear Georgi,
> > MA5616 does not have any SCU interface...
> > What can we do?
> >
> >
> > On Sun, Aug 11, 2013 at 4:17 PM, Georgi Genov <linuxloader () gmail com<mailto:linuxloader () gmail com>>wrote:
> >
> > > It`s configurable under scu/scuh/giu board
> > >
> > > interface scu 0/9
> > > native-vlan 1 vlan XXXX
> > > native-vlan 2 vlan YYYY
> > > or
> > > interface   giu 0/19
> > > native-vlan 1 vlan XXXX
> > > native-vlan 2 vlan YYYY
> > >
> > > On 11.8.2013 г. 09:33 ч., Shahab Vahabzadeh wrote:
> > >
> > > > Dear Friends,
> > > > Anybody have idea about changing native vlan on Huawei MA5616 DSLAM?
> > > > I can not find the correct syntax, there is no option under "interface
> > > > eth
> > > > 0/0"
> > > > Thanks
> >
> >
> > --
> > Regards,
> > Shahab Vahabzadeh, Network Engineer and System Administrator
> >
> > Cell Phone: +1 (415) 871 0742<tel:%2B1%20%28415%29%20871%200742>
> > PGP Key Fingerprint = 8E34 B335 D702 0CA7 5A81  C2EE 76A2 46C2 5367 BF90
>
>
>
> --
> Regards,
> Shahab Vahabzadeh, Network Engineer and System Administrator
>
> Cell Phone: +1 (415) 871 0742<tel:%2B1%20%28415%29%20871%200742>
> PGP Key Fingerprint = 8E34 B335 D702 0CA7 5A81  C2EE 76A2 46C2 5367 BF90



--
Regards,
Shahab Vahabzadeh, Network Engineer and System Administrator

Cell Phone: +1 (415) 871 0742<tel:%2B1%20%28415%29%20871%200742>
PGP Key Fingerprint = 8E34 B335 D702 0CA7 5A81  C2EE 76A2 46C2 5367 BF90



--
Regards,
Shahab Vahabzadeh, Network Engineer and System Administrator

Cell Phone: +1 (415) 871 0742
PGP Key Fingerprint = 8E34 B335 D702 0CA7 5A81  C2EE 76A2 46C2 5367 BF90