nanog mailing list archives
Re: <Help --> Having trouble trying to activate a GigE connection>
From: Peter Sandström <peter () stardoll com>
Date: Wed, 25 Nov 2009 10:39:23 -0800
I have seen this behavior caused by a mismatch of SFPs, SX on one side and LX on the other. /p On Tue, Nov 24, 2009 at 9:04 AM, Michael Ruiz <mruiz () telwestservices com> wrote:
I don't think there is any reason to have hard-set speed and duplex, particularly between two Cisco's. Why not just set *both* sides (you can't set just one) to auto-negotation - 'no speed nonegotiate' on the 7606 side. Is this a straight shot, single fiber pair between the two or are there intermediate junctions or optics? It sounds like you have questionable fiber or optics in the path. It could be the fiber itself or the GBICs on either side.Mike, I tried setting the 7206 to auto, and the 7606 to nonnegtiate, however, no dice. We put light meter on both ends of the GBIC and light readings are at -20, which are applicable. Between the two routers are MMF and it is straight shot with no transport equipment in between. -----Original Message----- From: Michael K. Smith - Adhost [mailto:mksmith () adhost com] Sent: Tuesday, November 24, 2009 10:25 AM To: Michael Ruiz; nanog () nanog org Subject: RE: <Help --> Having trouble trying to activate a GigE connection> Hello Michael:-----Original Message----- From: Michael Ruiz [mailto:mruiz () telwestservices com] Sent: Tuesday, November 24, 2009 8:02 AM To: nanog () nanog org Subject: <Help --> Having trouble trying to activate a GigEconnection>Group, I am having an issue with activating a Gige interface between a Cisco 7206 VXR w/IO-1GE module to a 7606 w/sup720-3bxls connecting to a line module WS-X6416-GBIC. I have verified that the GBIC-MMF have good light reading and the MMF fiber jumper are not reversed. The GigE connection comes up briefly for about a few seconds, takes a burst of errors and goes down. I have tried to set the speed to nonegotiate on both ends, set one end to speed auto. No dice. Hereisthe copy of the configuration. On my 7606 I show that the GigE interface is up/up but on the 7206vxr I show down/down. Any help will be greatly appreciated. Thanks!I don't think there is any reason to have hard-set speed and duplex, particularly between two Cisco's. Why not just set *both* sides (you can't set just one) to auto-negotation - 'no speed nonegotiate' on the 7606 side. Is this a straight shot, single fiber pair between the two or are there intermediate junctions or optics? It sounds like you have questionable fiber or optics in the path. It could be the fiber itself or the GBICs on either side. Regards, Mike
-- Peter Sandström Head of Operations, Stardoll AB phone: +46 (0)70 456 05 28 e-mail: peter () stardoll com | stardoll: pj0tr mail/visit: Hudiksvallsgatan 8, 113 30 Stockholm, Sweden www.stardoll.com - Fame, fashion and friends
Current thread:
- <Help --> Having trouble trying to activate a GigE connection> Michael Ruiz (Nov 24)
- RE: <Help --> Having trouble trying to activate a GigE connection> Michael K. Smith - Adhost (Nov 24)
- RE: <Help --> Having trouble trying to activate a GigE connection> Scott Berkman (Nov 24)
- RE: <Help --> Having trouble trying to activate a GigE connection> Michael Ruiz (Nov 24)
- Re: <Help --> Having trouble trying to activate a GigE connection> Peter Sandström (Nov 25)
- RE: <Help --> Having trouble trying to activate a GigE connection> Michael Ruiz (Nov 25)
- RE: <Help --> Having trouble trying to activate a GigE connection> Michael K. Smith - Adhost (Nov 24)